Antminer S4
Antminer S4 fan specification and possible replacement fans
This article will help you find replacement fans for your Antminer S4. Also we want to emphasize that if you have S4 under warranty do not use fans that are mentioned below as you will loose your warranty and Bitmain will not be responsible for any damage caused by your device. List of fans below is when you have no other option and/or your warranty is expired.
We must note one more time that these fans are NOT INTENDED TO BE USED with ANTMINER and you are using them on your own risk.
First you can see original Antminer S4 fan spec:
Dimension: 120*120*38mm
Voltage: 12V
Start voltage: ≧8V (Power ON/OFF)
Power consumption: 1600RPM 1.68W / 4000RPM 25.8W
Rated current: DutyCycle 100% @ 2.15A
Air Flow: 4000RPM @ 178.3CFM (Max be 239CFM)
Noise: 4000RPM @ 56.7 dB-A (Measured in a Non-EchoChamber)
Air Pressure: 1600RPM 2.88 MM-H2O (4000RPM 16.9 MM-H2O)
Life Expectancy: 40,000 hrs @ 25℃ (May degrade faster at higher temperature)
Connector: 2510-4P
Now we know what specs we need here are a few fans that will do the job properly.
Antminer S5
Antminer S5 fan specification and possible replacement fans
Specifications
Hash Rate: 1155 GH/s ±5%
Power Consumption: 590 W (at the wall)
Power Efficiency: 0.51 J/GH (at the wall)
Rated Voltage: 12V
Dimensions: 298 mm x 137 mm x 155 mm
Cooling: 1x 12038 fan
Operating Conditions: 0 °C to 35 °C
Certified By: FCC / CE
Network Connection: Ethernet
Notes
1. Power consumption figures vary with your PSU’s efficiency, the ambient operating temperature and the accuracy of the power meter.
2. PSU: A power supply unit is not included, and you will need to provide an ATX PSU. There are 4 PCI-e connectors for +12V DC input and all four are required. Do not connect more than one PSU to the same hashing board.
3. When better power efficiency is needed in the future due to higher network difficulties, you may want to buy some special PSUs 9V DC with more than 10A output, which will allow you to have a 0.2J/GH mining efficiency, but at lower hashing speed.
Building upon the foundation from the S1 and S3, the Antminer
S5 retains the same small form factor of previous miners, but, with the more
efficient BM1384 chips. The S5 uses 1 fan for quieter home operation and features
multiple improvements over the strong S3 design.
Specifications
Hash Rate: 1155 GH/s ±5%
Power Consumption: 590 W (at the wall)
Power Efficiency: 0.51 J/GH (at the wall)
Rated Voltage: 12V
Dimensions: 298 mm x 137 mm x 155 mm
Cooling: 1x 12038 fan
Operating Conditions: 0 °C to 35 °C
Certified By: FCC / CE
Network Connection: Ethernet
Notes
1. Power consumption figures vary with your PSU’s efficiency, the ambient operating temperature and the accuracy of the power meter.
2. PSU: A power supply unit is not included, and you will need to provide an ATX PSU. There are 4 PCI-e connectors for +12V DC input and all four are required. Do not connect more than one PSU to the same hashing board.
3. When better power efficiency is needed in the future due to higher network difficulties, you may want to buy some special PSUs 9V DC with more than 10A output, which will allow you to have a 0.2J/GH mining efficiency, but at lower hashing speed. - See more at: https://centrix-intl.com/details.asp?Parent2ID=1&productid=13250#sthash.A7CbY6dR.dpuf
Specifications
Hash Rate: 1155 GH/s ±5%
Power Consumption: 590 W (at the wall)
Power Efficiency: 0.51 J/GH (at the wall)
Rated Voltage: 12V
Dimensions: 298 mm x 137 mm x 155 mm
Cooling: 1x 12038 fan
Operating Conditions: 0 °C to 35 °C
Certified By: FCC / CE
Network Connection: Ethernet
Notes
1. Power consumption figures vary with your PSU’s efficiency, the ambient operating temperature and the accuracy of the power meter.
2. PSU: A power supply unit is not included, and you will need to provide an ATX PSU. There are 4 PCI-e connectors for +12V DC input and all four are required. Do not connect more than one PSU to the same hashing board.
3. When better power efficiency is needed in the future due to higher network difficulties, you may want to buy some special PSUs 9V DC with more than 10A output, which will allow you to have a 0.2J/GH mining efficiency, but at lower hashing speed. - See more at: https://centrix-intl.com/details.asp?Parent2ID=1&productid=13250#sthash.A7CbY6dR.dpuf
Building upon the foundation from the S1 and S3, the Antminer
S5 retains the same small form factor of previous miners, but, with the more
efficient BM1384 chips. The S5 uses 1 fan for quieter home operation and features
multiple improvements over the strong S3 design.
Specifications
Hash Rate: 1155 GH/s ±5%
Power Consumption: 590 W (at the wall)
Power Efficiency: 0.51 J/GH (at the wall)
Rated Voltage: 12V
Dimensions: 298 mm x 137 mm x 155 mm
Cooling: 1x 12038 fan
Operating Conditions: 0 °C to 35 °C
Certified By: FCC / CE
Network Connection: Ethernet
Notes
1. Power consumption figures vary with your PSU’s efficiency, the ambient operating temperature and the accuracy of the power meter.
2. PSU: A power supply unit is not included, and you will need to provide an ATX PSU. There are 4 PCI-e connectors for +12V DC input and all four are required. Do not connect more than one PSU to the same hashing board.
3. When better power efficiency is needed in the future due to higher network difficulties, you may want to buy some special PSUs 9V DC with more than 10A output, which will allow you to have a 0.2J/GH mining efficiency, but at lower hashing speed. - See more at: https://centrix-intl.com/details.asp?Parent2ID=1&productid=13250#sthash.A7CbY6dR.dpuf
Specifications
Hash Rate: 1155 GH/s ±5%
Power Consumption: 590 W (at the wall)
Power Efficiency: 0.51 J/GH (at the wall)
Rated Voltage: 12V
Dimensions: 298 mm x 137 mm x 155 mm
Cooling: 1x 12038 fan
Operating Conditions: 0 °C to 35 °C
Certified By: FCC / CE
Network Connection: Ethernet
Notes
1. Power consumption figures vary with your PSU’s efficiency, the ambient operating temperature and the accuracy of the power meter.
2. PSU: A power supply unit is not included, and you will need to provide an ATX PSU. There are 4 PCI-e connectors for +12V DC input and all four are required. Do not connect more than one PSU to the same hashing board.
3. When better power efficiency is needed in the future due to higher network difficulties, you may want to buy some special PSUs 9V DC with more than 10A output, which will allow you to have a 0.2J/GH mining efficiency, but at lower hashing speed. - See more at: https://centrix-intl.com/details.asp?Parent2ID=1&productid=13250#sthash.A7CbY6dR.dpuf
Antminer S6
Antminer S7 fan specification and possible replacement fans
- Hash Rate: 4.73 TH/s ±5%
- Power Consumption: 1293W ±10%
- Power Efficiency: 0.25 W/GH ±10%
- Requires 10x 6 pin pci-e connectors
- Power Supply required and sold seperately
Dimensions: 301mm(L)*123mm(W)*155mm(H), Cooling: 2x 12038 fan Operating Temperature: 0 °C to 40 °C, Network Connection: Ethernet, Default Frequency: 700M
Please note the following:
1. Power consumption figures will vary with your PSUs efficiency, the ambient operating temperature and the accuracy of the power meter. Figures provided are at the wall, with AC/DC 93% efficiency, and 25°C ambient temp.
2. PSU: A power supply unit is not included, and you will need to purchase one separately. There are 3 PCI-e connectors for +12V DC input on each hashing board and all 3 are required on each board. Do not connect more than one PSU to the same hashing board!
3. Separate power supply to control board: there is one additional 6pin PCI-e connector on the IO board which must be connected to the PSU to get power. If you use different PSU for hash boards and control board, please make sure to power the hash boards first and the control board only after the hash boards have been powered.
Antminer S9
New AntMiner S9 with 14 TH/s 16nm technology! The most efficient AntMiner EVER!
This Antminer S9 is not only the first 16nm miner for retail use, using
less than half the energy per gigahash of the S7, but it is also our
most powerful miner to enter mass production . At 0.098 joules per
gigahash, this is the most efficient machine available to the bitcoin
mining public.
S9 Specifications:
1. Hash Rate: 14.0TH/s ±5%
2. Power Consumption: 1375W + 7% (at the wall, with APW3 ,93% efficiency, 25C ambient temp)
3. Power Efficiency: 0.098 J/GH + 7%(at the wall, with APW3 93% efficiency, 25°C ambient temp)
4. Rated Voltage: 11.60 ~13.00V
5. Chip quantity per unit: 189x BM1387
6. Dimensions: 350mm(L)*135mm(W)*158mm(H)
7. Cooling: 2x 12038 fan
8. Operating Temperature: 0 °C to 40 °C
9. Network Connection: Ethernet
10. Default Frequency: 650M
Notes:
1.
Power consumption figures will vary with your PSU's efficiency, the
ambient operating temperature and the accuracy of the power meter.
2.
PSU: A power supply unit is not included, and you will need to
provide an ATX PSU. There are 3 PCI-e connectors for +12V DC input on
each hashing board and all 3 are required. Do not connect more than one
PSU to the same hashing board!
Bitmain recommends the APW3-12-1600-B2 power supply for use with the S9. One power supply support one S9.
4.
Separate power supply to control board: there is one additional 6pin
PCI-e connector on the IO board which must be connected to the PSU to
get power. Be sure to power on the miner after ALL the 10x PCIE
connectors connected to power supply.
Building upon the foundation from the S1 and S3, the Antminer
S5 retains the same small form factor of previous miners, but, with the more
efficient BM1384 chips. The S5 uses 1 fan for quieter home operation and features
multiple improvements over the strong S3 design.
Specifications
Hash Rate: 1155 GH/s ±5%
Power Consumption: 590 W (at the wall)
Power Efficiency: 0.51 J/GH (at the wall)
Rated Voltage: 12V
Dimensions: 298 mm x 137 mm x 155 mm
Cooling: 1x 12038 fan
Operating Conditions: 0 °C to 35 °C
Certified By: FCC / CE
Network Connection: Ethernet
Notes
1. Power consumption figures vary with your PSU’s efficiency, the ambient operating temperature and the accuracy of the power meter.
2. PSU: A power supply unit is not included, and you will need to provide an ATX PSU. There are 4 PCI-e connectors for +12V DC input and all four are required. Do not connect more than one PSU to the same hashing board.
3. When better power efficiency is needed in the future due to higher network difficulties, you may want to buy some special PSUs 9V DC with more than 10A output, which will allow you to have a 0.2J/GH mining efficiency, but at lower hashing speed. - See more at: https://centrix-intl.com/details.asp?Parent2ID=1&productid=13250#sthash.Qp5GXFXI.dpuf
Specifications
Hash Rate: 1155 GH/s ±5%
Power Consumption: 590 W (at the wall)
Power Efficiency: 0.51 J/GH (at the wall)
Rated Voltage: 12V
Dimensions: 298 mm x 137 mm x 155 mm
Cooling: 1x 12038 fan
Operating Conditions: 0 °C to 35 °C
Certified By: FCC / CE
Network Connection: Ethernet
Notes
1. Power consumption figures vary with your PSU’s efficiency, the ambient operating temperature and the accuracy of the power meter.
2. PSU: A power supply unit is not included, and you will need to provide an ATX PSU. There are 4 PCI-e connectors for +12V DC input and all four are required. Do not connect more than one PSU to the same hashing board.
3. When better power efficiency is needed in the future due to higher network difficulties, you may want to buy some special PSUs 9V DC with more than 10A output, which will allow you to have a 0.2J/GH mining efficiency, but at lower hashing speed. - See more at: https://centrix-intl.com/details.asp?Parent2ID=1&productid=13250#sthash.Qp5GXFXI.dpuf
Building upon the foundation from the S1 and S3, the Antminer
S5 retains the same small form factor of previous miners, but, with the more
efficient BM1384 chips. The S5 uses 1 fan for quieter home operation and features
multiple improvements over the strong S3 design.
Specifications
Hash Rate: 1155 GH/s ±5%
Power Consumption: 590 W (at the wall)
Power Efficiency: 0.51 J/GH (at the wall)
Rated Voltage: 12V
Dimensions: 298 mm x 137 mm x 155 mm
Cooling: 1x 12038 fan
Operating Conditions: 0 °C to 35 °C
Certified By: FCC / CE
Network Connection: Ethernet
Notes
1. Power consumption figures vary with your PSU’s efficiency, the ambient operating temperature and the accuracy of the power meter.
2. PSU: A power supply unit is not included, and you will need to provide an ATX PSU. There are 4 PCI-e connectors for +12V DC input and all four are required. Do not connect more than one PSU to the same hashing board.
3. When better power efficiency is needed in the future due to higher network difficulties, you may want to buy some special PSUs 9V DC with more than 10A output, which will allow you to have a 0.2J/GH mining efficiency, but at lower hashing speed. - See more at: https://centrix-intl.com/details.asp?Parent2ID=1&productid=13250#sthash.Qp5GXFXI.dpuf
Specifications
Hash Rate: 1155 GH/s ±5%
Power Consumption: 590 W (at the wall)
Power Efficiency: 0.51 J/GH (at the wall)
Rated Voltage: 12V
Dimensions: 298 mm x 137 mm x 155 mm
Cooling: 1x 12038 fan
Operating Conditions: 0 °C to 35 °C
Certified By: FCC / CE
Network Connection: Ethernet
Notes
1. Power consumption figures vary with your PSU’s efficiency, the ambient operating temperature and the accuracy of the power meter.
2. PSU: A power supply unit is not included, and you will need to provide an ATX PSU. There are 4 PCI-e connectors for +12V DC input and all four are required. Do not connect more than one PSU to the same hashing board.
3. When better power efficiency is needed in the future due to higher network difficulties, you may want to buy some special PSUs 9V DC with more than 10A output, which will allow you to have a 0.2J/GH mining efficiency, but at lower hashing speed. - See more at: https://centrix-intl.com/details.asp?Parent2ID=1&productid=13250#sthash.Qp5GXFXI.dpuf
Building upon the foundation from the S1 and S3, the Antminer
S5 retains the same small form factor of previous miners, but, with the more
efficient BM1384 chips. The S5 uses 1 fan for quieter home operation and features
multiple improvements over the strong S3 design.
Specifications
Hash Rate: 1155 GH/s ±5%
Power Consumption: 590 W (at the wall)
Power Efficiency: 0.51 J/GH (at the wall)
Rated Voltage: 12V
Dimensions: 298 mm x 137 mm x 155 mm
Cooling: 1x 12038 fan
Operating Conditions: 0 °C to 35 °C
Certified By: FCC / CE
Network Connection: Ethernet
Notes
1. Power consumption figures vary with your PSU’s efficiency, the ambient operating temperature and the accuracy of the power meter.
2. PSU: A power supply unit is not included, and you will need to provide an ATX PSU. There are 4 PCI-e connectors for +12V DC input and all four are required. Do not connect more than one PSU to the same hashing board.
3. When better power efficiency is needed in the future due to higher network difficulties, you may want to buy some special PSUs 9V DC with more than 10A output, which will allow you to have a 0.2J/GH mining efficiency, but at lower hashing speed. - See more at: https://centrix-intl.com/details.asp?Parent2ID=1&productid=13250#sthash.A7CbY6dR.dpuf
Specifications
Hash Rate: 1155 GH/s ±5%
Power Consumption: 590 W (at the wall)
Power Efficiency: 0.51 J/GH (at the wall)
Rated Voltage: 12V
Dimensions: 298 mm x 137 mm x 155 mm
Cooling: 1x 12038 fan
Operating Conditions: 0 °C to 35 °C
Certified By: FCC / CE
Network Connection: Ethernet
Notes
1. Power consumption figures vary with your PSU’s efficiency, the ambient operating temperature and the accuracy of the power meter.
2. PSU: A power supply unit is not included, and you will need to provide an ATX PSU. There are 4 PCI-e connectors for +12V DC input and all four are required. Do not connect more than one PSU to the same hashing board.
3. When better power efficiency is needed in the future due to higher network difficulties, you may want to buy some special PSUs 9V DC with more than 10A output, which will allow you to have a 0.2J/GH mining efficiency, but at lower hashing speed. - See more at: https://centrix-intl.com/details.asp?Parent2ID=1&productid=13250#sthash.A7CbY6dR.dpuf
